1s TinyShark

Save $90.00

These ultralight 2" drones are made to fly on 1s whoop batteries! Using the TinyFish ultralight 16x16 stack with included receiver!

TinyShark Frame

Wheelbase 95mm
Prop size 2"
Weight 6g
Arm Dimensions 2mm thick, 7.5-6.3mm wide

Racerstar 1103 Motors

Brand: Racerstar 
Item No: BR1103B 10000KV Brushless Motor
Height: 15mm
Width: 13.6mm
Weight: about 3.7g
Shaft: φ1.5mm
KV (rpm/V): 10000KV 
Voltage: 3.7-11.1V
Battery: 1-3S lipo battery

H02 Camera


  • FPV Micro AIO Camera 5.8G 40CH 25mW Transmitter for tiny whoop Blade Inductrix.
  • Light weight only 3.6g, Small size with 47 * 14.8 * 12.5 mm.
  • Supporting touch switch select channel Frequency group,Supporting NTSC/PAL switch, Support vertical inverted image switch.
  • 8 LEDs display channel and 5 LEDS display frequency group information, 1 LED display PAL/NTSC and FLIP information.


  • Output power: 25mW
  • Supply Voltage: 2.9-5.5v
  • Size : 47 * 14.8 * 12.5 mm
  • Weight: 3.6g
  • Antenna: Exclusive Dipole Whip Antenna
  • Power consumption: 200~215MA5V DCIN
  • Frequency: 5.8GHz 5 bands 40 channels, with Raceband: 5362~5945MHz
  • Field of view: 120º
  • Operating Temperature: -10℃~+60℃
  • Ambient temperature:25℃
  • Channel SEL:Touch Switch
  • Channel Indicate:CH1~CH8 Channel indication with 8LEDS and A~F frequency, group Indicate with 5LEDS
  • Modulation type:FM
  • Transmit power: 13±1dBm
  • Frequency control: PLL
  • All harmonic: Max -50dBm
  • Frequency Stability: ±100KHz (Typ.)
  • Frequency precision: ±200KHz (Typ.)
  • Channel Carrier error: 1dB
  • Antenna Port: 50 Ω
  • SENSOR:PAL: 720X540/NTSC:640X480 1/4”
  • LENS ANGEL: H:120°/V:100°
  • Base-band interface: (P1.27*2)
  • Profile dimension: 14.5mm*12.2mm+14.5mm*12mm

TinyFish Stack

The Lumenier tinyFISH Power Stack combines both a F3 Flight Controller and 4A 4-in-1 ESC into a compact stack. It uses a powerful F3 processor along with top of the line hardware. Now you can get all the performance from an F3 based flight controller in a truly micro size! This flight controller uses 16x16mm mounting holes and a low profile design allowing for smaller airframe designs than ever before. The tinyFISH comes with BetaFlight pre-installed.

The tinyFISH F3 Flight Controller has a built 8CH SBUS FrSky compatible receiver, making setup a breeze. This Power Stack has been designed by and named after our friends at fishpepper.de under an open source license.

4-in-1 ESC


  • 16x16mm M2 hole-to-hole spacing (20x20mm outer dimension)
  • a total weight of 1.2g (!)
  • BLHeli_S
  • DSHOT600 (rev 0.5 and higher)
  • regenerative breaking
  • 4.3A continuous current
  • openhardware + opensource software

Please note that this board is for 1S operation only. Do not even try 2S, the board will be immediately releasing all it’s magic smoke and stop working…


  • Input: 1s Lipo
  • Constant: 4.3 Amps
  • Burst: 5 Amps
  • Weight: 1.3g
  • Dimensions: 21x21x2mm
  • Mounting Dimensions: 16x16mm
  • Motor wire: 70mm
  • Signal wire: 140mm
  • MCU: BusyBee2 MCU at 48MHz
  • PCB - 4 Layer Blind Pole PCB - 3oz Pour
  • Mosfet: N-Channel
  • BEC: OPTO (none)
  • Supports Damped mode, Oneshot125 and Multishot. DSHOT 

Flight Controller

Software/Hardware Features

  • 1-3S Direct Lipo input support (3-12v) (LiPo power is required for PC connectivity!)
  • 16x16mm hole to hole spacing (20x20mm outer dimension)
  • Integrated FrSky compatible SBUS receiver (basically an integrated uSKY rx)
  • STM32F3 CPU
  • MPU-6000 SPI gyro
  • Supports DSHOT
  • Integrated Blackbox dataflash
  • Integrated voltage- and current-sensor
  • Buzzer output
  • RGB led output
  • Open hardware


  • CPU: STM32F3
  • SPI: ICM-20608-G Accelerometers and Gyroscope
  • Mounting Hole: 16x16mm, M2
  • Can support current, voltage monitoring
  • 2.4G Receiver 
  • Channel: 8CH
  • SUBS Output
  • Control Range: 200m
  • Compatible with Frsky X9D Plus Transmitter

Note: HV-charged batteries will not work, only one motor will spin till the battery discharges below 4.2v

You recently viewed

Clear recently viewed