Ascent X 2.5″ – FPV Racing Drone

$159.99

FlexRC Ascent X 2.5″ is an ultra light (only around 14g) and durable FPV racing drone frame with rolling cage for up to 2.5"propellers and Micro FPV Camera with 19mm mounting.

FlexRC Ascent X features X layout for extremely stable flight characteristics and good carbon fibers alignment for advanced durability. It is compact, very easy to build, offers great protection for drone's electronics and easy access to all the components for simple repair-ability

EMAX RS1106 Micro Brushless Motor

Legendary RS power for micro FPV racing quadcopters

The RS1106 has 6mm tall stator to provide the instantaneous torque that is usually lacking in high KV 1104 motors. The RS1106 is also one of the only micro brushless motors with active cooling fins integrated into the bell to keep magnets cooler so the power is consistent lap after lap.

For micro builds it’s important to have as little mechanical vibration to get the best performance from your flight controller. To ensure smoothness each motor is precision CNC, uses premium ball bearings and comes factory balanced.

 The bell housing has two sizes of hole spacing to fit the EMAX 2345 Tri-Blade and M2 x 5mm that works with a wide range of other 2” class propellers. Two lengths  of mounting screws are included for so it will fit a wide range of frame styles. 

RS1106 6000KV is a versatile upgrade motor for 2s-3s and well suited for those wishing to spin heavier 4 blade or 5 blade propellers.


Caddx Turbo EOS 2


This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.


This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.

Lumenier SM-25 25mW Micro VTX

This is the Lumenier SM-25, a Super Mini 25mW 5.8GHz 32CH FPV Transmitter. The lower 25mW transmission power means more pilots can fly together without overpowering each other on close frequencies. The SM-25 has 32 channels including the new Raceband frequencies. 

The SM-25 features an easy to use single button, LED interface. It is micro in size and only weighs 2.1g! It stays cool to the touch during operation, so you don't have to worry about it overheating in a crash.

Anniversary Special Edition Eachine Minicube Flytower

Frequency range: 2.403-2.479Ghz
Channels: 8CH 
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST 
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)

Eachine Minicube 10A BLHeli_S 4 In 1 ESC:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 2-3S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on

Features:
STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky
Jaw-dropping flight performance
LED_STRIP solder pin
BUZZER Ready
Betaflight support
Acro mode / Air mode /Angle mode support 
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
OSD Configuration has been include in BETAFLIGHT GUI
Radio Stick to control PID Tunes

You recently viewed

Clear recently viewed