Whoop Crossfire BT2.0

$169.99

*F4 1S AIO Brushless Flight Controller (NO RX)

F4 1S AIO FC(SPI Rx) integrates 4 components as F411 FC, 5A ESC, 25mW VTX and SPI receiver. It is ultralight only 3.92g and still maintains an amazing performance capability, which makes it become your best choice to run with a 1S brushless quad! 

F4 1S AIO FC(No Rx) integrates 3 components as F411 FC, 5A ESC and 25mW VTX. It supports external receivers like TBS Crossfire, Frsky XM+ and Spectrum DSMX etc. Meanwhile, this version can handle the 2S power system. 

Bullet Point

  • Integrated with a 25mW VTX, this AIO board(Frsky/Futaba Rx) is ultralight only 3.92g, which can extremely save the weight of building drone, perfectly suitable for the 1S weight-sensitive drone such as Meteor65 HD and HX100 SE.
  • F4 1S AIO FC(No Rx) not only integrates with the 25mW VTX but also supports a 1-2S power system, which is perfectly suitable for the weight-sensitive drone such as Meteor75 and Beta85 Pro2
  • This AIO board also reserves a Plug & Play port for the C01 Camera, C01 Pro Camera and BETAFPV Nano HD Camera, no soldering work needed, super convenient for installation.
  • Specially added with 2 RGB LED indicators, this board brings the drone an incredible light effect while pilots flying on the night. 
  • This board can handle 5A continuous current(6A burst), supports the 1S lipo battery, brings the drone a stronger flight performance. 
  • Come with a BT2.0 connector, it solves the problem of voltage sag, the discharge can be more efficient, which brings this board a better performance on function for power and responsiveness. 

Specification of F4 1S AIO FC(SPI Rx)

  • Item: F4 1S AIO FC(Frsky/Futaba Rx)
  • Weight: 3.92g(without antenna and BT2.0 connector)
  • VTX Power: 25mW
  • CPU: STM32F411CEU6 (100MHZ )
  • Six-Axis: MPU6000 (SPI connection)
  • Firmware version: betaflight_4.2.0_STM32F411
  • Receiver: Support Frsky Receiver/ Futaba Receiver
  • Motor Pin Connecter: 1.25mm Header Pins
  • Mounting hole size: 29mm x 29mm / suitable for almost all kind of whoop frame

Specification of ESC

  • Built-in ESC with 5A continuous and peak 6A current
  • Input voltage: 1S Lipo
  • ESC firmware: O_H_5_REV16_8.HEX 
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
  • 4 Indicators: Receiver indicator (Blue)/Flight control status indicator (Green)/Flight control power indicator (Red)/VTX indicator (Pink)

Diagram for F4 1S AIO FC(SPI Rx)

SPI Receiver CC2500

Come with the build-in SPI Receiver CC2500, F4 1S AIO FC(SPI Rx) can compatible with Futaba S-FHSS, Frsky D8 and D16 protocol. The default Frksy protocol is Frsky D16, if pilots buy the wrong receiver of the SPI Frsky version or upgrade the wrong firmware accidentally, which needs to switch the protocol to Futaba or FrskyD8, please upgrade the Betaflight Firmware according to this tutorial. 

Configuration

Protocol

FRSKY_D

Frsky D8

FRSKY_X

Frsky D16 FCC

FRSKY_X_LBT

Frsky D16 LBT

SFHSS

Futaba S-FHSS

Status LED for F4 1S AIO FC(SPI Rx)

There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED ( Blue), FC Status LED(Green), FC Power LED ( Red ) and VTX LED(Pink).

LED

Status

Description

Receiver LED ( Blue)

Solid

Connected or in bind mode

Receiver LED ( Blue )

Flashing

Not connected

Power LED ( Red )

Solid

Power on

Status LED ( Green )

Solid

Motor Armed

Status LED ( Green )

Flashing

Motor Disarmed

Status LED ( Green )

Off

Bind

VTX LED ( Pink )

Flash Slowly

Work

Recommended Parts of F4 1S AIO FC(Frsky/Futaba Rx)

  • Battery: BT2.0 300mAh 1S Battery / BT2.0 450mAh 1S Battery / BT2.0 260mAh 1S Battery
  • Frame:  Meteor65 Frame / Meteor75 Frame
  • Props: 31mm 4-Blades props / 40mm 4-blades props
  • Motors: 0603 motors / 0703 motors / 0802 motors / 0802SE 22000KV Motor 
  • Camera: C01 Camera / C01 Pro Camera / BETAFPV Nano HD Camera

Specification of F4 1S AIO FC(No Rx)

  • Item: F4 1S AIO FC(No Rx)
  • Weight: 3.83g (without antenna and BT2.0 connector)
  • VTX Power: 25mW
  • CPU: STM32F411CEU6 (100MHZ )
  • Six-Axis: MPU6000 (SPI connection)
  • Firmware version: betaflight_4.2.0_STM32F411
  • Receiver: Support External Receiver, SPI Receiver, including Frsky XM/XM+ receiver, Futaba receiver, Crossfire receiver and DSMX receiver
  • Motor Pin Connecter: 1.25mm Header Pins
  • Mounting hole size: 29mm x 29mm / suitable for almost all kind of whoop frame

Specification of ESC

  • Built-in ESC with 5A continuous and peak 6A current
  • Input voltage: 1S Lipo
  • Input voltage: 1-2S Lipo
  • ESC firmware: S_H_70_REV16_7.HEX 
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
  • 4 Indicators: Receiver indicator (Green)/Flight control status indicator (Blue)/Flight control power indicator (Red)/VTX indicator (Pink)

Diagram for F4 1S AIO FC(No Rx)

How to Connect the External Rx to the FC(No Rx)

For more convenience to the pilots, we specially design the Plug & Play SPI Frsky Rx for the F4 1S AIO FC(No Rx), no soldering work needed, super easy to install.  

Receiver Connection Diagram


Status LED for F4 1S AIO FC(No Rx)

There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED ( Blue), FC Status LED(Green), FC Power LED ( Red ) and VTX LED(Pink)

LED

Status

Description

Receiver LED ( Green)

Solid

Connected or in bind mode

Receiver LED ( Green)

Flashing

Not connected

Power LED ( Red )

Solid

Power on

Status LED ( Blue )

Solid

Motor Armed

Status LED ( Blue )

Flashing

Motor Disarmed

Status LED ( Blue )

Off

Bind

VTX LED ( Pink )

Flash Slowly

Work

Recommended Parts of F4 1S AIO FC(No Rx)

  • Battery: BT2.0 300mAh 1S Battery / BT2.0 450mAh 1S Battery / BT2.0 260mAh 1S BatteryBT2.0 300mah 2S Battery
  • Frame:  Meteor65 Frame / Meteor75 Frame / Beta85 Pro2 Frame
  • Props: 31mm 4-Blades props / 40mm 4-blades props / Gemfan 2020 4-Blades Props
  • Motors: 0603 motors / 0703 motors / 0802 motors / 0802SE 22000KV Motor / 1103 11000KV motors / 1102 18000KV motor
  • Camera: C01 Camera / C01 Pro Camera / BETAFPV Nano HD Camera

Package

  • 1 * F4 1S AIO Brushless Flight Controller
  • 4 * M1.2x4mm Screws
  • 4 * M1.4x5mm Screws
  • 4 * Anti-vibration Rubber dampers

*TBS CROSSFIRE NANO RX

TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX we condense 2 years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case, the minimum!). The end result is a full range receiver, at the smallest size of any receiver in the industry (yes, it's smaller than the XM+). 

SPECIFICATIONS

  • Weight: 0.5g (receiver only)
  • Size: 11mm x 18mm
  • Requires: Firmware V2.25

INCLUDES

  • 1x TBS Crossfire Nano Receiver
  • 1x TBS Crossfire Micro Receiver Antenna
  • 1x Spare shrink tube
  • 6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
  • 1 x pin header 1x4

*0802SE Brushless Motors

0802SE 22000KV/19500KV motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.83g/pc but also ensuring the awesome performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexible and longer flying time. What' more, we highly recommend using it on the weight-sensitive 65mm brushless whoop drone, such as the Meteor65 HD.

Bullet Point

  • 0802SE 22000KV/19500KV motor is a lightweight 1S motor, specially designed for 1S whoop drone-like Meteor65 HD.
  • Compared with the 0802 series brushless motors, 0802SE 22000KV has significantly reduced the weight, which is only 1.83g/pc. It still ensures the awesome performance of power and thrust.
  • Compared with 0802 19500KV brushless motors, 0802SE 19500KV is reduced by 0.15g, which is only 1.8g. While it is used on a 65mm drone, pilots can get a  more flexible flight and can fly longer.
  • If you are trying a stronger violent indoor flight, 22000KV is ideal for you. If you wanna get a longer flight, 19500KV will be more suitable. 
  • 0802SE Motor makes the perfect dynamic balance, which gives the drone more flexible and longer flying time, which is perfect for the weight-sensitive 65mm brushless whoop drone.
  • Lead wire soldered to the PCB, which allows you to repair it easier once it disconnected.
  • Compared with 0802 19500KV brushless motors, 0802SE 19500KV is reduced by 0.15g. When it is used on a 65mm drone, it is more flexible and can fly longer


Specification

  • Item: 0802SE 22000KV/19500KV brushless motor
  • Weight: 1.83g/pc
  • Color: Black
  • Shaft length: 5mm
  • Shaft diameter: 1mm
  • Hole distance: 6.6mm
  • Motor Mount Holes: M1.4
  • Input Voltage: 1S
  • Cables: 25mm long, 30AWG cables
  • Dimensions: 10.5*10.5*13.6mm
  • Bearings: Brass Bushings

Recommended Parts

  • Propellers: 31mm 4-blade props
  • Frame: Meteor65 frame
  • FC: F4 1S Brushless FC /F4 1S AIO FC
  • Battery: 1S Battery

Package

  • 4 * BETAFPV 0802SE Brushless Motors
  • 1 * Pack of M1.4*3 Screws

*NewBeeDrone 65mm Cockroach Brushless Super-Durable Frame

Frustrated with constantly fixing struts and breaking frames, we set out to find something better.

We worked with a number of manufacturers and after numerous prototypes and revisions, we are proud to introduce the Cockroach Super-Durable Brushless Frame for Tiny Whoop style quads.

Traditional Looks and Geometry maintain those flight characteristics you are used to and ensure easy compatibility with the Beebrain as well as most other popular flight controllers.

Lightweight and Durable. We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls. Total weight 3.71g

Easy and Inexpensive. None of this is any good if its super difficult to use and super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine tuned to make installation and removal much easier.

*4 pairs Gemfan 1219 1.2x1.9x3 31mm 1mm hole 3 propellers

4 pairs Gemfan 1219 1.2x1.9x3 31mm 1mm hole 3 propellers for 0703-1103 Drone RC FPV Racing Brushless Motor 

Specification:
Brand Name: Gemfan 
Item Name: 1219 31mm 1mm Hole propeller 3 blades 
Number of blades: 3 blades 
plot: 2 inches 
Material: PC 
Weight / G: 0.28g 
Diameter of the central hole: 1mm 
diameter disk palette: 31mm 
center thickness: 5 mm 
maximum width blade: 5.71mm 
Motor adaptation 0703-1103 recommended Motor: 0703 hollow cup 

Package included:
4 x 1219 CW 31mm 1mm hole 3 propeller blades 
4 x 31mm 1mm hole 1219 CCW propellers propeller 3
 

*C02 FPV Micro Camera

C02 Micro Camera is the lightweight camera customized for those weight sensitive micro whoop drones, like Meteor65, Beta65S, Beta85 pro2, HX100SE. Adapted a 1/4'' CMOS sensor, 2.1mm lens for  1200TVL resolution and excellent latency while minimizing the weight to 1.4g. Packed with the micro canopy, protect your camera well in a hard crash. 





Plug-N-Play 

C02 camera features a JST-0.8 connector, special design in plug-and-play, makes it easy to install without soldering. Suitable for BeeBrain flight controllers.

Bullet Points

  • Miniature, and lightweight design, weight at only 1.4g. Best match with 5.8G A01 VTX on micro whoop drone.
  • 1200TVL resolution and 1/4" CMOS sensor ensure a high-quality and clear image
  • Global WDR camera, 16:9 aspect ratio, shoot clear dynamic image even in low light condition
  • 2.1mm lens, FOV 160° beyond the wide-angle for recording more wide and beautiful scenes
  • The package comes with an injection molding canopy, more durable, which is the best combo with C02 camera



      Specification

      • Item: C02 Camera
      • Image Sensor: 1/4" CMOS Sensor
      • Horizontal: 1200TVL with Global WDR
      • Signal System: NTSC
      • Lens : 2.1mm(M8) FOV 160°
      • S/N Ratio: >50db
      • Electronic Shutter Speed: Auto
      • Auto Gain Control (AGC): Auto
      • Min. Illumination: 0.01Lux@1.2F
      • D-WDR: Auto
      • Day/Night: Color
      • Power: DC 3-5.5V
      • Current: 110mA@5V / 120mA@3.3V
      • Housing Material: ABS
      • Dimension: 13*11mm
      • Net weight: 1.4g



            Package

            • 1 * C02 FPV Micro Camera
            • 1 * Injection Molded Canopy
            • 1 * 1/4'' Camera Mounting hardware

            *NewBeeDrone BeeBrain Goober Canopy

            The Goober canopy was made for maximum protection on your BeeBrain Lite board, and looking great with a stream-line stingray inspired shape.

            The canopy uses a neck collar that goes around the BeeEye camera and screws into place holding it securely together to hold up to tough impacts and crashes. A front cap covers the top of the camera lens to help make sure front impacts resist hitting your lens, or as we like to call it "the dad hat".

            If you broke the neck collar of your Goober Canopy, grab a replacement neck collar.

            3D Print Parts

            Insta Go Mount on Goober Canopy- Design by Dalton

            You recently viewed

            Clear recently viewed